GMC

2005 GMC Yukon

CRM Mitchell1 2021-04-06T22:02:15+00:00

Mileage

107,097

Service Date

4/5/2021

Services Performed

• replaced faulty water pump.
• Verified concern – pressure tested system, found coolant actively leaking from water pump – recommend replacement

 

Alan V. gave our service a 5 star review on 4/5/2021

2005 GMC Yukon CRM Mitchell1 2021-04-06T22:02:15+00:00

2008 GMC Yukon

CRM Mitchell1 2021-03-14T22:01:57+00:00

Mileage

174,308

Service Date

3/12/2021

Services Performed

• after modules were replaced complete setup(vehicle configuration) was not performed causing air bag light. updated all control units with current programs, verified correct programs to each module, completed vehicle configuration and module set up as required when control units replaced and air bag light and code for configuration now gone.
• oil pressure gauge not reading any oil pressure. removed switch and checked pressure was 40 psi at idle. replaced faulty oil pressure sending unit with factory GM oil sending unit and now gauge working properly.
• Raised the vehicle in the air and disconnected the front drive shaft from the differential and unbolted the axles from the front differential and then removed the front differential to gain access to the motor mounts. Removed the bolts from the motor mount in the frame. Then used a pole Jack to raise the motor to gain access to the motor mount bolts in the motor. Remove the motor mounts and then remove the starter to remove the right side motor mount. Remove both mount and installed the new mounts. Reassembled and test drove the vehicle everything is good at this time.
• Raised the vehicle in the air and then remove the front drive shaft from the differential and both axles. Remove the front differential to gain access to the differential Mount brackets. Remove the broken Mount brackets and installed the new ones. Test drove the vehicle everything is good at this time.
• Road test vehicle. Change oil and oil filter. Rotate tires as needed. Lubricate chassis as needed. Perform Vehicle inspection. Adjust tire pressure. Fill windshield washer fluid.
• Test drove vehicle. Raised on lift and performed vehicle inspection. Filled out vehicle condition report and submitted to service advisor.
• vehicle came in and had following codes stored P0230 fuel pump primary circuit, P0523 engine oil pressure sending unit, P069E fuel control module requested mil, P025A fuel control module A, P0523 brake switch, P1175 fuel trim bank 2. cleared all codes and codes for fuel control module came back right away. verified control unit programming and set up. connector at fuel pump control module was broken and had been zip tied to housing to secure. tested circuit from FPCM power and grounds and found signal circuit from FPCM pin 13 dark green wire/white had been bypassed and power from pin 15 had been spliced into that wire and had been run back to PCM signal wire pin 50. P0230 code setting by PCM due to signal wire was bypassed. removed wiring done elsewhere and isolated short in circuit to harness had rubbed on front driveshaft causing short in circuit to PCM. repaired 2-wires damaged by drive shaft including green/white wire that had been bypassed. replaced 20 amp fuse to FPCM circuit fuse 21 and now PCM sending fuel pump control signal and code P0230 now resolved.
• Re-flash program from GM

 

Jonathon S. gave our service a 5 star review on 3/13/2021

2008 GMC Yukon CRM Mitchell1 2021-03-14T22:01:57+00:00

2004 GMC Envoy

CRM Mitchell1 2021-03-07T23:00:45+00:00

Mileage

140,065

Service Date

3/1/2021

Services Performed

• Raise the vehicle in the air and removed the clips from the old fender liner. Removed the old fender liner and installed the new fender liner and reinstalled the clips.

 

Charles B. gave our service a 5 star review on 3/6/2021

2004 GMC Envoy CRM Mitchell1 2021-03-07T23:00:45+00:00

2004 GMC Envoy

CRM Mitchell1 2020-12-27T23:00:13+00:00

Mileage

138,789

Service Date

11/30/2020

Services Performed

• Remove the left front wheel. Disconnect the lower hose. Remove fasteners and replace the thermostat and housing. Reassemble, fill system and test drive the vehicle.
• Test drove the vehicle and found engine will not reach operating temperature due to defective thermostat.

 

Charles B. gave our service a 5 star review on 12/26/2020

2004 GMC Envoy CRM Mitchell1 2020-12-27T23:00:13+00:00

2019 GMC Yukon XL

CRM Mitchell1 2020-11-14T23:02:30+00:00

Mileage

40,480

Service Date

11/13/2020

Services Performed

• Completed inspection on tablet.
• Road test vehicle. Check all suspension and steering parts for wear. Check tire pressure and condition. Check riding height. Check alignment of all four wheels. Adjust caster, camber, toe-in, and thrust angle as needed on all four wheels. Center steering wheel and adjust steering angle as needed.
• Road test vehicle. Change oil and oil filter. Rotate tires as needed. Lubricate chassis as needed. Perform Vehicle inspection. Adjust tire pressure. Fill windshield washer fluid.

 

Kyle H. gave our service a 5 star review on 11/13/2020

2019 GMC Yukon XL CRM Mitchell1 2020-11-14T23:02:30+00:00

2012 GMC Acadia

CRM Mitchell1 2020-09-30T22:02:37+00:00

Mileage

124,757

Service Date

9/29/2020

Services Performed

• Remove both wiper blades then the cowling. Removed both front wheels. Removed the sway bar end links and the wheel speed sensors from the strut. Removed the struts and installed the new struts. Then performed an alignment and test-drove. Recommend replacing all four tires.
• Road test vehicle. Check all suspension and steering parts for wear. Check tire pressure and condition. Check riding height. Check alignment of all four wheels. Adjust caster, camber, toe-in, and thrust angle as needed on all four wheels. Center steering wheel and adjust steering angle as needed.

 

Troy E. gave our service a 5 star review on 9/29/2020

2012 GMC Acadia CRM Mitchell1 2020-09-30T22:02:37+00:00

2005 GMC Yukon

CRM Mitchell1 2020-08-07T22:01:08+00:00

Mileage

103,201

Service Date

8/4/2020

Services Performed

• Competed Inspection on Tablet
• Please hit all lube points on front chassis
• Road test vehicle. Change oil and oil filter. Rotate tires as needed. Lubricate chassis as needed. Perform Vehicle inspection. Adjust tire pressure. Fill windshield washer fluid.

 

Alan V. gave our service a 5 star review on 8/6/2020

2005 GMC Yukon CRM Mitchell1 2020-08-07T22:01:08+00:00

2012 GMC Acadia

CRM Mitchell1 2020-07-15T22:03:00+00:00

Mileage

129,818

Service Date

7/14/2020

Services Performed

• Accessed air box. Removed and replaced engine air filter. Cleaned excess debris form air box. Secured air box. Accessed cabin filter and removed. Sprayed BG Frigifresh on new filter and installed new cabin filter.
• Recovered freon from system. Removed and replaced high and low side schrader valves. Vacuumed system. Charged freon to proper capacity. Inspected AC lines and drive belt. Verified proper operation of AC system. Test drove the vehicle and found it to be running hot. Inspected the coolant level and it's down a couple points or so. The lower hose is only luke warm while the upper is hot, indicating no flow. Also, the water pump is leaking. Tested for a possible head gasket issue and no hydrocarbons present. Recovered the freon and found 1.1 lbs out of 2.3 present. No visible leaks apparent upon inspection.
• Remove the air filter intake and housing. Remove lower radiator and heater hoses. Remove fasteners and replace the thermostat housing. Reassemble, test drive and inspect repair.
• Road test vehicle. Change oil and oil filter. Rotate tires as needed. Lubricate chassis as needed. Perform Vehicle inspection. Adjust tire pressure. Fill windshield washer fluid.
• Test drove vehicle. Raised on lift and performed vehicle inspection. Filled out vehicle condition report and submitted to service advisor.

 

Lindsay K. gave our service a 5 star review on 7/14/2020

2012 GMC Acadia CRM Mitchell1 2020-07-15T22:03:00+00:00

2004 GMC Envoy

CRM Mitchell1 2020-01-13T23:00:31+00:00

Mileage

134,942

Service Date

1/6/2020

Services Performed

• Add cleaner to transmission. Test drive to verify operation and circulate cleaner. Use fluid exhnage machine to remove old fluid and add new. Add fluid conditioner and verify proper level. Test drive to verify proper operation.
• Completed inspection on tablet.
• Road test vehicle. Change oil and oil filter. Rotate tires as needed. Lubricate chassis as needed. Perform Vehicle inspection. Adjust tire pressure. Fill windshield washer fluid.

 

Charles B. gave our service a 5 star review on 1/12/2020

2004 GMC Envoy CRM Mitchell1 2020-01-13T23:00:31+00:00

2007 GMC Sierra Classic

CRM Mitchell1 2019-10-18T22:02:02+00:00

Mileage

99,435

Service Date

10/17/2019

Services Performed

• Remove the right rear wheel. Remove brake caliper and rotor. Remove axle flange and hub. Replace the broken stud and reassemble.
• Unable to duplicate concern this visit.

 

Lynn T. gave our service a 5 star review on 10/17/2019

2007 GMC Sierra Classic CRM Mitchell1 2019-10-18T22:02:02+00:00